Dashboard work...again

So the dashboard is coming on well. I'm very happy with the shape, it has a more natural feel to it.

I've sprayed parts black to help me find holes and high / low points. Below is how it currently looks

The next two bits to do are;

* Make a dial surround that also fits over the key hole.
* Fix new demist vents on top of dashboard.

I'm taking a new approach to the demister to lower the amount of piping. I will bond the below under the dashboard where the  the vent holes are.

I will then get both outlets to join under the dashboard and then go into this channel which will then feed out of two vents. The piece about is 660mm long so will fit fully across the dashboard.

After the above 2 pieces are done. I will look into starting the flocking.

Dashboard in and seats test fitted

So the dashboard had to be put in over the centre tunnel. It was a tight fit but in some ways that is good as it wont move. Ive only had to secure it to the cross member with 1 sturdy bolt just to hold it there and being honest I dont think it needed it other than for safety.

Once In I tested the dials and gauges all worked as well as the stereo.

All worked well and the look felt more natural. Next i made the vanity panel to go over the dials and the stereo. I actually mucked this up and got dirt under the wrap as I put it on the wrong side so it will need to be done again at some point.

I also put the buttons too far forward and only the hazard is accessible, lucky I can just drill new holes further back and move them.

The seats also go well with the dashboard and feel much comfier, however I will have to get rid of the seat rails and making them fixed, the extra cushioning has raised the position and the 25mm drop will be a big gain to have.

work has started (interior)

So first of all I got one last local meet in before the end of September and the weather changed. the cool evening air gave a nice crispness and punch to the engine as well.

So within a few days I was on to the job at hand...the interior. I'm in no rush to do this and will do it right rather then fast. So previously I had ordered my new seats. The criteria was I wanted small ones in terms of height and width and also reclining. Reclining was simply because there was a small amount of space behind the seats but with a fixed seat you simply cant get in there. With a reclining a hand luggage suitcase would fit or other bags you may want to put in out the way.

Luckily these were also one of the cheapest seats as well, which is rare to happen. The comfort of them compared with my current ones is like night and day so I'm very happy. They raise the seating position a little but I can counteract this by removing the carpet and sound deadening from underneath the mounting points so there will be little difference but more comfort, the seats also feel like they hold well for their shape.

so I test fitted one of the chairs, you can see even though they are the smallest reclining seat I could find there is little difference in size but they are slightly smaller, in theory they will probably be easier to get into as well.

So on to the interior and it came out easily enough, as I took it all out the dust from the bodywork was everywhere so ive done a fair bit of cleaning already and then moved on to tidying the new wires I had added once on the road. (tv screen, electric door opening).

Since then I've been measuring areas of the interior to start designing the new centre console between the chairs.

Clutch change, missfires and more

So my last statement was a jinx ' if everything was ok I may move on to the interior'.

First was my new set of coilovers had arrived and so I wanted to fit them ASAP!

Got them fitted and the awful banging I had has reduced a lot I've still had it a few times on large bumps but there isn't alot of travel available and a thin tyre wall but overall the Meister R coilovers have massively improved the ride.

Overall a success, as well as this the rear of car was able to go about another 10mm lower. Without the larger 20" wheels I dont think the arches will ever be as full as they look on the other DDR's but now it looks reasonable.



....So I had started to run with more power, slowly creeping up to the 1bar area of boost and then I felt some slip, I ignored it first time thinking one off, but decided to go out and do a 3rd gear pull from low revs and again I had a slight slip.

I knew I couldn't ignore it and didn't want to run low power! So I ordered a new clutch (toyota OEM) and prepared to fit it. The fitting then came...OH MY GOD!!! Advice, if you think your clutch is ok when the engine is out....it doesnt matter just change it! The job took a total of 10hrs and wasnt easy on a drive.

Engine mounts were removed, jacks used to hold engine in position straps to take the gearbox weight and then wiggling the gearbox off. To be fair that all wasn't too hard but just time consuming. Changing the actual clutch again was easy enough, although lining it up when it was at an angle was not.

However getting the gearbox back on was a nightmare it took best part of an hr and half to get the gearbox back on to the engine and I ended up using longer bolts to pull the gearbox back into position and on to the location pegs. Once done I started bolting everything back together.

Once done it was time for a quick test drive and it juddered a bit at first but even within 20miles that had almost gone so I was happy it was successful!

I was then due to go on holiday but wanted to stop a missfire at high boost! so got some contact cleaner, it was then I found the king lead from coilover to distributor was missing an end and was having to arc! So i got a replacement one and tested it and all worked as expected.

I then went on holiday for a week and this weekend had a 200mile+ round trip to do for an event, the longest single days journey without tinkering the car will of done to date. I was nervous but prep'd as much as I could.The Journey up went well and we arrived at the meeting point.

the above image shows the rear a bit lower now.

Next was a convoy to Mercedes Benz World where we'd park up fro the Brooklands supercar day, made it there fine and left the car parked up.

So then came the drive home, 100+miles of some motorways. about 10miles in I realised I couldn't make any boost, so I had barely any power. luckily 70mph was doable and that's what I cruised back at, any slight hill though had me worried!

When I got back and took a look at it the actuator rod had come off the wastegate. The wastegate stays shut and opens when boost hits the level set so you don't send too much boost into the engine and blow it up. I had the opposite the wastegate was just swinging about all by itself, mostly open. hence no boost. It looks like either the retaining clip had fallen off or was missing either way an easy fix which I've already done.

However it was a very annoying 70mile drive home with no power!

Developments

For once the good news is...everything has been smooth. The cars been running fine which is good. I took it for a midweek run as well after the previous weekend and everything was fine.

Following that I fitted the exhaust tip I wanted to use going forward and think it looked much better than the previous one.

I then spent the Saturday getting the car really clean, wash, polish, wax... there goes 3 - 4hrs of my life!

Then last weekend was Wilton House Supercar show and it was parked in the car park. Its first public outing and still not finished, the feedback from people was good and they liked the car, almost all questions were what is it. The only issue I have come across is from people thinking its a poor replica of a Mclaren F1. Its not although inspired. However a lot felt it had a Zonda front to it but I want to stop that so I definitely need to get some badges made up to solve that! Also I didn't do up the new twin exhaust I got... so fell off on the Saturday and was run over DOH! So i've re-dordered it again to refit.

As for the cleaning....shouldn't have bothered the path was like a dust bowl, better than mud but the car ended up like this down the side of the car.

The car drove great on the day and in some good heat and stayed really nice and cool running about 185 - 190f when driving, so perfect.

So whats next, well im now going to work a little on other touches like sealing up all the little gaps between the cockpit and engine bay and also the front arches just to help keep out a bit more noise.

Only bad thing to come out of this was the BC racing coilovers have previously leaked and all the oil has gone or too much air, do not get bc racing coilovers they are rubbish, barely done any miles and just sat on the car for ages. Instead I will enjoy a couple weekend of hard metal on metal banging when its a big bump!

I've also been looking into the rear wing again, now ive chopped off the ends, so just getting an idea on what to do.

I guess it would be rude now not to look and getting that 100bhp back I've lost, so time to up the power this weekend I think.

Recent work and finally driving it

First of all I completed the doors. This involved a few things, first was to fit the new blanking plates for the car and removing exterior door handles. This gave the car more security. the remote central locking is working well.

After this I fitted some open pocket foam inside the door, its light and will stop excessive noise as well. With the interior parts of the door completed it was at this stage I fitted some door cards just to tidy the doors up. the final finished article will be higher quality and match the dash etc... when done.

Next was the exhaust piece being completed, well there's few things I've got majorily wrong on this project, but this was one! It looked horrible, the design just did not suit the car. Im only sharing the picture for others so they don't go this route!!

So at the moment I have the original tip on for driving however a new tip has arrived already and I'm very happy with its look, I've just got to do some minor adjustments to it and it will be on and looking much better!

I've now set the front ride height at 85mm on both sides give or take a mm or two. This works well for me with the front arches looking full enough but allowing me to get on and off the drive without planks etc... At the end of the day I want to be able to use the car relatively easily. the rear will need to be lowered further in the future.

Next I had the side windows refitted, the current fitting was done in the bodyshop and there was too much dust in them when fitting with some areas lifting. As well as this I had a nice rubber edging added to give it a cleaner look.

The final side window bits are being fitted this week to finish the look off but I think it gives it a much nicer edge.

So then it came to driving it at the weekend. This was the first time since the engine had been put together and various other work. so I took it out, with the softer springs I fitted a while back the ride is better but still a bit softer at the front would be nicer. It has too much of that coilover 'bang' for my liking. The engine was now performing correctly and not eating water, so it does look like a poor fitting of the headgasket was the cause (should of done it myself in the beginning!).

Now whilst driving the car is not overheating, but it is running hot, ideally it should run up to about 195f and mine is running around 210f-215f. Now when on the drive it gets warm and the fans kick in but never gets higher then the 190f i'd expect. However once driving it raises slightly and sticks at that higher temps, so not overheating but just running hot. So I've had to look into why and what can I do to improve it.

I noticed the coolant pipe return from the radiator is very close to the downpipe, so the coolant is cooled at the radiator and then reheated just before re-entering into the engine. Meaning the water flowing into the engine is hotter then it should be, raising the operating temperature slightly. this doesn't happen on the drive at idle because the down pipe hasn't raised up to the hotter temperatures, as well as this the hot and cool pipes to the radiator run close to each other under the car, again not helping. The 2 pics below show where the pipe is now and the new path I'm going to do this week with a new pipe. Also a diagram of what it was like on the MR2 and you'll see its far away from the exhaust and the radiator pipes are separated.

As well as this other work I'm going to do to help temperatures;

1. The engine compartment temps feel high, when lifting the rear clam shell I can feel its warm, so id like to lower these, so I've ordered a turbo blanket to help.

2. Exhaust wrap for the downpipe. Now exhaust wrap is a debatable subject to many, however in this case keeping the temp inside the exhaust has a big benefit to not radiating onto other components and will also lower engine compartment temps with the the turbo blanket as well.

2. Ill also try and wrap / insulate the hot water feed to the radiator under the car so it does not radiate heat on to the returning pipe.

I think with the above I will drop 10f minimum, I actually think the biggest cause of heat into the system is the fact the coolant pipe is 1cm away from an unshielded downpipe!

So back to the drive, I managed to complete 90 miles without any actual overheating, eating of water etc... the car had no faults and ran as expected. If I can just lower the temperatures now a little bit for safety I can then work on lowering further intake temperatures, which will already benefit from the above as well.

The performance, well the turbo is still at 7psi (actuator pressure) and I wont turn the boost up until temps are under control. seeing as I haven't had the geometry done yet the car handles pretty well with minimal pull to one side.

Here's a quick video, sorry there isn't a good one yet. I've got to get them all on a video training course as I received a lot of videos of the floor.

Headlights, Doors, Undersealing and more

I've been trying to source some black bolts, harder then you'd think for the lengths I want. So in the meantime I painted carefully the top of the silver ones black to blend in more and get a feel for how it looks. It definitely makes the headlight covers look like they belong there a lot more but is obviously a subtle touch.

As well as this I Meshed the front reservoirs, Unfortunately it had to be a metal mesh which I always thinks looks very 'kitcar' however it has come out very well with a good fit and the black paint still covering it.

Next was to underseal the car and arches. So I took the wheels off and got on with the task, this is only coat one, which will do the job, however I expect ill put a 2nd coat on. Now I didn't use a car underseal for a couple of reasons, one they are very waxy and messy and too they are the same as another product which is priced cheaper. So I used a liquid rubber product normally used for putting on flat roofs, does the same job of stopping water from coming through and is flexible when dried.

Before:

After:

Now the top of the arches need to be done, but I also want to protect the fibreglass from stone chips, so I've ordered more closed cell foam, I can then paint this with the rubber before fitting and simply stick it in the arches, giving the additional rubber protection to the foam which should stop stones creating Star shapes in the fibreglass.

I have also fitted the door solenoids, so there are no door handles accessible from the outside giving more security. when I press the button I have 3 seconds to open the door before it relocks. This is all wired into the fusebox I fitted to the car at the beginning and uses relays. I will need to tidy the additional wiring once I get the dash off for the refit of that. In the video below you can hear the click of it relocking once open.

The rear camber bolts were next, which has definitely brought the rear wheels more vertical and hence look like they fill the arch that little bit more and will give some Geo adjustments when that is done.

I have also started on the interior door cars just to tidy up the giant hole so the doors dont look so bad when being opened! But more on that next time. In the meantime the two main items till I can drive the car are the side windows and the exhaust piece. I should have the exhaust finished this week and side windows in the next two weeks! (fingers crossed)

Engine Work

Following the work taking place on the engine to strip the head, it was sent off to a specialist who pressure tested it and also refaced it. I ordered a new cometic headgasket and fitted the engine back together. I had problems fitting the tight belt but got there eventually.

Before filling it with coolant I decided to try and fire it up, if id done something wrong I didn't want to have to drain it again! It wouldn't fire...

A quick google and a check and I hadn't connected the connector that connects on to the dizzy cap. Connected that and it fired straight into life. As well as this I took the opportunity to repaint the rocker cover black and also the heat shield (although keeping underneath silver). This just tidied up the engine a bit more as the rocker cover had peeled a lot.

Next is to finish the fitting of the exhaust (1st back box) and jack the rear of the car up whilst filling with coolant. Ill then run it at the same time to remove air from the system.... Hopefully!

Following that, it will need an oil filter and oil change to clear the system of any contaminations from during the work.

I can then move on to the other jobs;

* Fit rear camber bolts
* Arrange Geo Setup
* Get Rear side windows fitted
* Fit door solenoids
* Wire up rear view camera
* Complete exhaust tip and surrounding mesh
* Mesh over brake reservoirs

Then hopefully the exterior will be close to completion.

The good the bad and the ugly..

A fitting title to this update. so lets look at the good first.

I managed to get 120 miles under the belt and the car felt fast even though its only running 7psi and will be up'd to 15psi. That's about where the good ends in this update.

The bad was the car was overheating. Id try various things, fixing some minor leaks and then also adding some bumper vents to feed the radiator.

These kept temperatures stable and low but as soon as I went on boost that's when it overheated, also the car seemed to be drinking water and then the final part was the exhaust fumes smelled sweet....so I knew what the issue was. Either a cracked head or headgasket, my gut instinct was headgasket.

So the ugly...Apart came the engine, the good news is the block itself looks in good condition and I got on to cleaning the pistons and the block face, although the pistons were not that dirty and came clean easily which is good. Also with the large engine bay it was easy to do this work.

So the head is currently off being pressure tested and either refaced or skimmed this week. I've ordered some new hoses which ill replace that sit under the turbo as I may as well do it whilst the turbo is off saving another job in the future.

Although its annoying to have to do this, the job isn't actually that bad but purely because I have plenty of room to work in so hopefully have it back together by the end of the weekend and running again.

And finally here's a walkaround video...make sure you watch till the end for a clip of it on the road.

Pick up...

Not got a lot of time so its a quick update with the pictures doing the talking.

Picked the car up but still need to fit a few bits to it (rear camera fitting, mirror, exhaust changing!)...but here's some pics...or a lot

Bodyshop work

So the car has been at the bodyshop a while now and work has been going well. so the first time I went door they had lined up the doors and filled and smoothed relevant parts and put a layer of high build primer on.

I was impressed at this stage the work looked great, the only area which did not look really good to me was the lower door edge it stuck out too far, so it was agreed that would be built up to be matched. You'll notice the spoiler isn't done at this point.

Also the rear vents were not done and I couldn't decide on what to do I said to the bodyshop most importantly it cannot effect the strength of the piece and left it with them. They did a great job and did the below, really happy with them and it suits the lines of the car.

The car was almost ready for spraying and was in the final stages of being prep'd

So next I took the headlight covers and splitter away to be hydrodipped to match the wheels.

When I was bringing these back I got a surprise the car had been baked and sprayed! I'll let the pictures do the talking but its an understatement to say I was pleased with the results.

As you can see the 3 stage paint, varys well from sunlight to dull light which was exactly what I was after so it looked good on a cloudy day! the paint hasn't been flattened yet and I've been impressed with the reflection lines at this stage so I'm sure it will look amazing once detailed in the summer. wont be long till its put back together and I get it back.